Guralp-systems CMG-3T Manual de usuario Pagina 37
- Pagina / 53
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Operator's guide
adjustment motors. It responds to commands sent on three input lines
by grounding for 0.2 – 7 seconds.
The signals you can send to the microprocessor are termed LOCK,
UNLOCK, and CENTRE. Each command acts on the vertical, N/S and E/
W masses in turn. The microprocessor prevents the system from
attempting incompatible actions (e.g. centring when the masses are
clamped.)
While a command is taking place, if you are using a Hand-held Control
Unit, its BUSY LED will flash; you can use this for diagnostic purposes.
See the description of each command for full details.
When no command is active, i.e. all three lines are high, the control
microprocessor goes into a power-saving mode. In routine operation,
the lines are controlled from the breakout box, Hand-held Control Unit
or digitizer. If you send control signals to the 3T manually, you must
ensure that the lines are pulled high after sending the signal, or the
equipment may be damaged. A “biased-OFF” type switch can be used
for this purpose.
LOCK
This command locks the masses and clamps the horizontal sensors by
tilting them up to their end stops.
If LOCK is activated when the masses are already locked, the processor
will unlock them and attempt to lock again. This is useful if you
suspect that the locking procedure has failed.
In detail, the process acts as shown in the following graph. The top
three streams are the mass position outputs of each component (Z, N/S
and E/W, respectively), whilst the bottom one represents the state of
the BUSY LED (up = on).
July 2009 37
- Operator's guide 1
- Table of Contents 2
- 1 Introduction 3
- 1.1 Options 4
- Sensor control interface 5
- Sensor response 6
- 2 Installing the 3T 7
- Connections 8
- Power supply 9
- Signal output 9
- 2.2 Installation notes 10
- 2.3 Installing in vaults 11
- 2.4 Installing in pits 14
- Other installation methods 16
- 2.5 Installing in post-holes 18
- 3 Calibrating the 3T 20
- Poles and zeroes 21
- Frequency response curves 22
- 3.2 Calibration methods 23
- 3.3 Calibration with Scream! 23
- Sensor response codes 27
- 3.5 The coil constant 28
- 4 Accessories 30
- The meter 31
- Calibration 32
- Control commands 32
- 5 Inside the 3T 35
- 5.2 The control system 36
- 5.3 RS232 control interface 41
- 5.4 The feedback system 42
- Hybrid feedback 43
- Comparisons 45
- 46 Issue N 46
- 6 Connector pin-outs 47
- 7 Specifications 51
- 8 Revision history 53
Relacionado con productos y manuales para Herramientas Guralp-systems CMG-3T
Herramientas Guralp-systems CMG-5T Manual de usuario
(25 paginas)
(25 paginas)
Herramientas Guralp-systems CMG-6T Manual de usuario
(31 paginas)
(31 paginas)
Herramientas Guralp-systems CMG-6TD Manual de usuario
(108 paginas)
(108 paginas)
Loadstar-sensors Software Benutzerhandbücher
Die Liste der Loadstar-sensors Software -Produkte enthält 5 Benutzerhandbücher für 5 diese Modelle. Alle PDF-Benutzerhandbücher können heruntergeladen oder online angezeigt werden.
Comentarios a estos manuales